Mocal Thermostat, 1/2" BSD
MOC-601
Mocal Thermostat, 1/2" BSD
MOC-601
132,00 €
ar PVN
-0%
ar PVN
Piedāvāt cenu
Uzdot jautājumu
Norādītais piegādes termiņš ir informatīvs un noradīts kā aptuvenais piegādes termiņš ja prece ir pieejama piegādātāja noliktavā. Vairāk par piegādes nosacījumiem. Ja vēlaties precizēt piegādes termiņu, lūdzu nosūtiet mums ziņu.
Katrs maksājums
Apmaksājiet savus pirkumus 3 vienādās daļās, 3 mēnešu laikā. Bez procentiem vai komisijas maksas. Vienkārši maksājiet vēlāk! https://trackday.eu/esto-3
Piegāde Latvijā
Pasūtījumi vērtībā līdz 50 €
uz Omniva vai DPD pakomātu
uz Omniva vai DPD pakomātu
4,50 €
Pasūtījumi vērtībā virs 50 €
uz Omniva vai DPD pakomātu
uz Omniva vai DPD pakomātu
3.00 €
Piegāde ar kurjeru
9.00 € - 12.00 €
Apraksts
Mocal Thermostat, 1/2" BSD
Mocal Thermostat, 1/2" BSD
Prolonged use of a car engine in conditions where the oil cannot reach its correct working temperature will cause sludge formation and crankcase oil dilution, leading to excessive wear especially in the cylinder bores. Optimum engine power will only be delivered at correct temperatures. The elimination of drag in engines caused by cold oil is a most important consideration, especially with a racing engine, revving the engine without a load will not put much heat into the oil and devices for preheating the oil may not be available.
It is therefore desirable to control of the oil flow through the cooler by a thermostatic device, we call an oilstat, set to divert oil to the cooler at 80ºC (although a wide range of settings is available for special applications). This is the minimum temperature required to evaporate and dispel contaminating substances.
The bodies of the these units are die cast aluminium. Control is by a "waxstat", a mass produced item built to highest standards. They are light enough to be supported by the hoses, however a bracket is supplied with the slightly heavier OT/2, if further restraint is required. The oilstats should only be used where oil cooling is adequate, the sensing device will suffer permanent damage above 140°C, replacements are available.
Can be built into the oil cooler take off for most engines with spin-off filters, they add nothing to the thickness of the plate.
Are available as a separate unit to be fitted into the oil lines. Two sizes of oilstat for in line fitting are available.
Prolonged use of a car engine in conditions where the oil cannot reach its correct working temperature will cause sludge formation and crankcase oil dilution, leading to excessive wear especially in the cylinder bores. Optimum engine power will only be delivered at correct temperatures. The elimination of drag in engines caused by cold oil is a most important consideration, especially with a racing engine, revving the engine without a load will not put much heat into the oil and devices for preheating the oil may not be available.
It is therefore desirable to control of the oil flow through the cooler by a thermostatic device, we call an oilstat, set to divert oil to the cooler at 80ºC (although a wide range of settings is available for special applications). This is the minimum temperature required to evaporate and dispel contaminating substances.
The bodies of the these units are die cast aluminium. Control is by a "waxstat", a mass produced item built to highest standards. They are light enough to be supported by the hoses, however a bracket is supplied with the slightly heavier OT/2, if further restraint is required. The oilstats should only be used where oil cooling is adequate, the sensing device will suffer permanent damage above 140°C, replacements are available.
Can be built into the oil cooler take off for most engines with spin-off filters, they add nothing to the thickness of the plate.
Are available as a separate unit to be fitted into the oil lines. Two sizes of oilstat for in line fitting are available.
Specifikācija
| Zīmols | Mocal |
|---|