Mocal Thermostat, 1/2" BSD
MOC-601
Mocal Thermostat, 1/2" BSD
MOC-601
€132.00
with VAT
-0%
with VAT
Offer a price
Ask a question
The indicated delivery time is for informational purposes and is given as an approximate delivery time if the item is available in the supplier's warehouse. More about Ordering terms. If you would like to confirm the delivery time, please send us a message.
Each payment
Apmaksājiet savus pirkumus 3 vienādās daļās, 3 mēnešu laikā. Bez procentiem vai komisijas maksas. Vienkārši maksājiet vēlāk! https://trackday.eu/esto-3
Shipping in Latvia
Orders up to 50 €
to Omniva or DPD parcel locker
to Omniva or DPD parcel locker
4,50 €
Orders over 50 €
to Omniva or DPD parcel locker
to Omniva or DPD parcel locker
3.00 €
Courier delivery
9.00 € - 12.00 €
Description
Mocal Thermostat, 1/2" BSD
Mocal Thermostat, 1/2" BSD
Prolonged use of a car engine in conditions where the oil cannot reach its correct working temperature will cause sludge formation and crankcase oil dilution, leading to excessive wear especially in the cylinder bores. Optimum engine power will only be delivered at correct temperatures. The elimination of drag in engines caused by cold oil is a most important consideration, especially with a racing engine, revving the engine without a load will not put much heat into the oil and devices for preheating the oil may not be available.
It is therefore desirable to control of the oil flow through the cooler by a thermostatic device, we call an oilstat, set to divert oil to the cooler at 80ºC (although a wide range of settings is available for special applications). This is the minimum temperature required to evaporate and dispel contaminating substances.
The bodies of the these units are die cast aluminium. Control is by a "waxstat", a mass produced item built to highest standards. They are light enough to be supported by the hoses, however a bracket is supplied with the slightly heavier OT/2, if further restraint is required. The oilstats should only be used where oil cooling is adequate, the sensing device will suffer permanent damage above 140°C, replacements are available.
Can be built into the oil cooler take off for most engines with spin-off filters, they add nothing to the thickness of the plate.
Are available as a separate unit to be fitted into the oil lines. Two sizes of oilstat for in line fitting are available.
Prolonged use of a car engine in conditions where the oil cannot reach its correct working temperature will cause sludge formation and crankcase oil dilution, leading to excessive wear especially in the cylinder bores. Optimum engine power will only be delivered at correct temperatures. The elimination of drag in engines caused by cold oil is a most important consideration, especially with a racing engine, revving the engine without a load will not put much heat into the oil and devices for preheating the oil may not be available.
It is therefore desirable to control of the oil flow through the cooler by a thermostatic device, we call an oilstat, set to divert oil to the cooler at 80ºC (although a wide range of settings is available for special applications). This is the minimum temperature required to evaporate and dispel contaminating substances.
The bodies of the these units are die cast aluminium. Control is by a "waxstat", a mass produced item built to highest standards. They are light enough to be supported by the hoses, however a bracket is supplied with the slightly heavier OT/2, if further restraint is required. The oilstats should only be used where oil cooling is adequate, the sensing device will suffer permanent damage above 140°C, replacements are available.
Can be built into the oil cooler take off for most engines with spin-off filters, they add nothing to the thickness of the plate.
Are available as a separate unit to be fitted into the oil lines. Two sizes of oilstat for in line fitting are available.
Specification
| Manufacturer | Mocal |
|---|